T shirt Hack no. 2

 

TH2full1

Inspired by a jacket worn by Jenna Lyons, I bought a ladies basic T shirt and with a few additions,  have styled it into a lightweight modern jacket. This would be a good piece for any capsule wardrobe. If you are interested in working with stripes T shirt hack no 1.

Best T shirt for this hack:

Look for a white t shirt that is made of medium weight 100% cotton fabric. I am using a long sleeve crew neck tee that I found online. Hanes, beefy T shirt would be a good weight. Avoid any tissue weight or synthetics fabrics like rayon or poly, they are too soft and won’t have enough substance for a jacket.

You will also need 1 yard of white cotton muslin, not natural muslin.

 

th2Insp2

Determine the length (L) of the jacket body by measuring from your neckline down to your natural waist, add .5 inch seam for attaching the peplum.

Measure and mark this (L) dimension on t shirt with tailors chalk. Cut along the line, preserving the bottom portion of the t shirt for jacket ties.

th2make1

Cut along the center front of the body.

th2make3

Measure, mark and trim bottom section of t-shirt into 1.25″ strips.

 

Cut Front Panel Pieces from white cotton muslin. Measure 9 inch for the width and use the (L) length of trimmed body  + .5 inches, remember to cut 2 pieces.

th2make4

Pin the Length of the front panel to the front of the jacket, allowing .5″ seam to overlap neckline.

Stitch a .5″ seam, press open.

th2make6

At fold line, fold front panel piece so that right side of fabric is on the inside.
Making sure to fold back remaining .5″ seam.

Stitch across top, just above neckline. Trim seam allowance and grade seams where to remove bulk.

th2make7

Turn right side out, press, pin and topstitch along edges. I stitched close to the edge on 3 sides and 3/8″ on inside edge for visual interest.

th2make8Cut the peplum pieces above from the muslin.

Fold peplum pieces along fold line with right side of fabric on inside, stitch side seams.

th2make9

On center back, stitch the notch.

th2make10

Trim and turn pieces right side, use a pin to straighten corners and press.

th2make11

Align and pin peplum to jacket body. Sew seam, open and press.

How to make jacket ties

Holding one end of the 1.25″ strips, pull until the strip curls/edges roll.

th2make12

Mark 4 or 5 lines on both sides of jacket front.

th2make13

Using a wide zig zag stitch, secure ties at markings.

th2make14

Here it is. I hope you like it.
Please comment below with any thoughts, suggestions or questions.

Thank you for taking a look at my t-shirt hack!

T-shirt Hack No. 1

Convert an old striped T-shirt into a modern bolero jacket.

IMG_1629

First, measuring the length of your jacket. Mark the t-shirt near the waistline, you will be adding a peplum approx. 1.5 inches later.

IMG_1630

Align the shoulder seams, side seams and neckline edge, creating a center front fold line.

Cut along fold upward through the neckline.

IMG_1631

From the lower portion of the t-shirt, trim approximately 2 inches all across the bottom ( including the original hem).

This will become the peplum on the bottom of the jacket.

tshirtcrop512300

 

Trim off the side seam of the center panel, align the two layers, matching stripes.

Measure your jacket body length and + 1″ for seams (1/2″ seam for top and bottom of front panel).

This will be the length, for the width allow 5″ mark with chalk and trim
(ex. my jacket body length is 9″ so I am cutting a 10″ L x 5″ W rectangle).

 

peplumadd

With right sides facing each other pin the peplum to jacket body all around the hem and trim the excess.

pepchalk2

 

Using tailors chalk, mark a stitching line starting from side seam, below the tshirt original hem (where ruler grid overlaps overlocked stitching on T-shirt hem) to the center of jacket front, 1/4 inch above raw edge.

e6d72-img_1693

If you are using a standard machine, reducing the pressure on the presser foot will allow for easier sewing. Use a zigzag stick or stretch stitch setting if available.

ae599-img_1668

Sew the peplum onto the jacket body following the chalk line.

On the back continue straight across so that the finished peplum will be approximately .5″ length in the back.

Press, trim seam and topstitch.

0ae4c-thack1mis402x-100

Oops, didn’t photograph this step; so I created a simple diagram using Illustrator.

Pin the interfaced edge of front panel to front edge of jacket. Overlaping 1/2″ on top and 1/2″ over jacket lower seam. Stitch from top to red dot (stopping at lower jacket seam).

Press open seam, pressing allowance towards front panel/away from jacket body.

needle

Roll front edge of peplum inward .5″ hand stitch.

Fold front panel at center line. Stitch .5″ seam at the top and bottom of center panel.

grade1

Grade seams on front panel at corner and seam allowance to reduce thickness.

Turn center panel right side out.

IMG_1711

Hand-stitch inside of front panel and voilà you are finished!

IMG_1725

 

I hope you enjoyed this tutorial. Please comment below with any
suggestions or questions.

Thank you!